Glad to be here... - Scroll Saw Woodworking & Crafts Message Board

corymike · 06-15-2012, 02:47 AM

Just getting back into scrolling after several years away. I am currently in the process of refurbishing my Delta 16 in scroll saw with plans to try my hand at scrolled bowls. Prior to my extended hiatus I had been involved in scrolling for about 5 years, and general woodworking for more than 30 years. I look forward to getting to know the folks here in this community, sharing ideas and experiences.

HAMMER · 06-15-2012, 02:13 PM

Welcome back I am sure you will be up to speed in no time... there are plenty of patterns and tips here at this forum if you need a refresher so feel free to jump in and use the forum as you need.

Just remember we need pictures or else it is just words..... no pictures it didn't happen.

corymike · 06-15-2012, 05:21 PM

I promise, I will post plenty of pics as I get things going. Just spent the morning at the hardware store hunting assorted screws and scrounging items to finish getting this saw back into operation and build some incarnation of dust collection.
With the screws I found I should have the saw at least working, though I fear the work surface is going to require a trip to the local machinist. I had stored it in my dads barn and what at first looked like surface rust actually has pitted it a good deal

Ah well, what fun would it be without a little challenge from time to time?

06-15-2012, 02:47 AM	#1
corymike Junior Member Join Date: Apr 2012 Posts: 5 Thanks: 0 Thanked 0 Times in 0 Posts	Glad to be here... Just getting back into scrolling after several years away. I am currently in the process of refurbishing my Delta 16 in scroll saw with plans to try my hand at scrolled bowls. Prior to my extended hiatus I had been involved in scrolling for about 5 years, and general woodworking for more than 30 years. I look forward to getting to know the folks here in this community, sharing ideas and experiences.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Sure glad today is over...	will8989	Off Topic	6	04-04-2011 09:40 PM
Glad to be back!	mikej	Off Topic	3	12-07-2008 11:44 PM
glad to be here	muleskinnerldb	Welcome Members	4	11-08-2008 11:44 PM
very glad to be here	Terry Grimm	Welcome Members	2	11-08-2008 10:59 PM
Glad to get Home	JohnB	Off Topic	7	02-18-2008 05:04 AM

06-15-2012, 02:13 PM	#2
HAMMER Senior Member Join Date: Apr 2008 Location: KATY, TX. (WEST HOUSTON) Posts: 1,109 Thanks: 5 Thanked 8 Times in 6 Posts	Welcome back I am sure you will be up to speed in no time... there are plenty of patterns and tips here at this forum if you need a refresher so feel free to jump in and use the forum as you need. Just remember we need pictures or else it is just words..... no pictures it didn't happen.

06-15-2012, 05:21 PM	#3
corymike Junior Member Join Date: Apr 2012 Posts: 5 Thanks: 0 Thanked 0 Times in 0 Posts	I promise, I will post plenty of pics as I get things going. Just spent the morning at the hardware store hunting assorted screws and scrounging items to finish getting this saw back into operation and build some incarnation of dust collection. With the screws I found I should have the saw at least working, though I fear the work surface is going to require a trip to the local machinist. I had stored it in my dads barn and what at first looked like surface rust actually has pitted it a good deal Ah well, what fun would it be without a little challenge from time to time?