Newbe from Maiden Nc - Scroll Saw Woodworking & Crafts Message Board

Jerry74 · 09-23-2009, 06:07 PM

I bought a hitachi CW-40 about 6 month ago and just started playing with it i got laid off in june so after all the honey do list i Know have a chance to try to work withit some maybe i can learn to use it properly

ubgoofy2003 · 09-23-2009, 06:33 PM

Hi, Jerry, welcome to the forum. You'll find a lot of information here, if you need help with anything. Have a question, just ask & someone will respond. Just make sure you use good blades for your scroll work. They are very important & also the vibration of your saw. Have it mounted on a good solid base. Then you decide if you would rather sit while you cut or stand. Decisions, Decisions. Hope you enjoy the saw & let us see some of your work when you finish one. Good Luck
Perk

DBourdon · 09-23-2009, 07:16 PM

Hey Jerry,

Welcome to the forum. Plenty of info here and help to be had if needed. Just ask.

Cheers,
Don

Jerry74 · 09-23-2009, 09:12 PM

well I did it i just sent for a varity pack of flying dutchmans

guitarman · 09-24-2009, 12:17 AM

Always nice to welcome another tar heel to the forum. Where in N.C. is Maiden? David

Jerry74 · 09-24-2009, 12:20 AM

Maiden is about 45 min north of charolet and 10 min south of hickory

guitarman · 09-24-2009, 12:22 AM

That gives me an close idea where you are. I'm about 10 miles west of Winston-Salem. David

Jerry74 · 09-27-2009, 06:59 AM

Thats cool I come down that way about every two weeks and go to blue ridge wholesale I help run a salt water fish and coral store called dav's pet shop

ncsealeveler · 09-27-2009, 02:10 PM

Howdy and welcome.Great folks here and lots of info.Tony

09-23-2009, 06:07 PM	#1
Jerry74 Junior Member Join Date: Sep 2009 Posts: 10	Newbe from Maiden Nc I bought a hitachi CW-40 about 6 month ago and just started playing with it i got laid off in june so after all the honey do list i Know have a chance to try to work withit some maybe i can learn to use it properly

09-24-2009, 12:17 AM	#5
guitarman Senior Member Join Date: Mar 2007 Location: Lewisville, N.C. Posts: 869	Always nice to welcome another tar heel to the forum. Where in N.C. is Maiden? David __________________ ole' yellar and me are great friends

09-24-2009, 12:22 AM	#7
guitarman Senior Member Join Date: Mar 2007 Location: Lewisville, N.C. Posts: 869	That gives me an close idea where you are. I'm about 10 miles west of Winston-Salem. David __________________ ole' yellar and me are great friends

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-23-2009, 06:33 PM	#2
ubgoofy2003 Senior Member Join Date: Mar 2007 Location: Arizona Posts: 486	Hi, Jerry, welcome to the forum. You'll find a lot of information here, if you need help with anything. Have a question, just ask & someone will respond. Just make sure you use good blades for your scroll work. They are very important & also the vibration of your saw. Have it mounted on a good solid base. Then you decide if you would rather sit while you cut or stand. Decisions, Decisions. Hope you enjoy the saw & let us see some of your work when you finish one. Good Luck Perk

09-23-2009, 07:16 PM	#3
DBourdon Member Join Date: Dec 2007 Location: Lenoir, NC Posts: 48	Hey Jerry, Welcome to the forum. Plenty of info here and help to be had if needed. Just ask. Cheers, Don

09-23-2009, 09:12 PM	#4
Jerry74 Junior Member Join Date: Sep 2009 Posts: 10	well I did it i just sent for a varity pack of flying dutchmans

09-24-2009, 12:20 AM	#6
Jerry74 Junior Member Join Date: Sep 2009 Posts: 10	Maiden is about 45 min north of charolet and 10 min south of hickory

09-27-2009, 06:59 AM	#8
Jerry74 Junior Member Join Date: Sep 2009 Posts: 10	Thats cool I come down that way about every two weeks and go to blue ridge wholesale I help run a salt water fish and coral store called dav's pet shop

09-27-2009, 02:10 PM	#9
ncsealeveler Senior Member Join Date: Nov 2008 Location: Sea Level NC Posts: 266	Howdy and welcome.Great folks here and lots of info.Tony