DeWalt 788 Easy-Lift Sytem?

[JimSawyer]

I was just wondering if anyone has used the Easy-Lift system for the 788. Right now I've got a piece of wood that I stick in there to hold up the upper arm. I haven't had any real problems. But it has gotten in my way when threading a hole deep in the pattern. Does it work? Is it easy to use? Is it worth the $20 ?

[ozarkhillbilly]

Hello Jim, I personally don't have one nor ever used one, but feed back from those who do have always been positive It's a good concept and I think a fair price.

I top feed with my Dewalt and really have no trouble raising the arm with my left hand and threading the blade with my right. I guess its what you get used to.
I'd rather spend the $20.00 on wood,blades,patterns.............

[Dragon]

I've tried Marcel's saw and he has one. I thought it was great. I will eventually get myself one. It is much better than the piece of wood.
Diane

[JoelM]

This is probably a dumb question, but....
do you raise the upper arm and leave the blade in the top clamp, or do you remove the blade from both clamps, raise the arm out of the way, then thread the blade? I haven't been raising the arm at all, I just remove the blade and rethread with the upper arm down.

[Janette]

I have the easy lift system and think it's great. The only thing I noticed with it is that I have to hold the arm down a bit prior to tightening the blade, but that's probably just because of how I have the tension adjusted on it. I put the blade in on top, tighten the bottom, then go and retighten the top, holding the arm down - then do the tension , which I find is perfect around 31/2 or 4.

[Minnesota scroller]

Joel, if bottom feeding, release the top of the blade, raise the upper arm, and then thread the top of the blade thru the hole in the bottom of the wood. Of course, you have to hold the wood as high as possible to be able to see under it to find the holes. Then reclamp. No, it's not a dumb question. If you don't ask, you don't learn.

However, I'm with Bill regarding top feeding. I don't really see any value to this if use his method. If I was still bottom feeding, I would probably consider the Jim Dandy.

[JoelM]

I top feed, but I've never raised the arm. I just remove the blade, reposition the wood and drop the blade through another hole. I suppose if I did raise the arm there would be more room. I'll have to give it a try.

[Minnesota scroller]

Originally Posted by JoelM

I top feed, but I've never raised the arm. I just remove the blade, reposition the wood and drop the blade through another hole. I suppose if I did raise the arm there would be more room. I'll have to give it a try.

Joel, while top feeding, I hold the arm up and feed the blade with my right hand and guide the wood with my left. Once the blade is in the hole, I slowly lower the arm.

[JimSawyer]

Wow, I never even considered bottom feeding. I'll have to give that a go and see how it works. When I had my old Taiwanees saw, it had a blade clamp on the bottom and an easy-jig for the top, so I've always been accustomed to top feeding. Picture that. I would pull the blade clampp from the bottom, position mypiece on the table, at an angle, push the blade up through the table and into the piece, (all this with my neck at a 98 degree angle,ouch). then lock the top with the quick-jig. Hey, not for nothing, I did some pretty incredible work like that, (what was I thinking. Give me my 788 any day).
So I guess I'll have to try that bottom feeding thing. Still, will I have to crane my neck to lock the bottom clamp? Thanks for the imput, all.

[unixpro]

I'm a bottom feeder and I have the easy-lift attached to my saw. I couldn't imagine doing without it. Cut, right hand moves left to detension, unscrew the blade, lift the arm, locate the next hole and feed the blade through. Screw the blade down, right hand pushes the top down and retensions the blade, then hits the power button on the top. It can become a real rhythm there after a while.