DeWalt Scroll saws

[Daryl185]

a question for those of you who own the dewalt saws?, which model dewalt has the lift arm? I have seen several remanufactured dewalt 788 but it seems like the upper arms are solid pieces.

I will soon be advancing past my current saw I am afraid due to the limitations of blade changing as for now I generaly feed the blade from the bottom of the wood its easier and faster then pulling the blade out tilting the table reinserting the blade realigning the table ect............ TIA

[Marcel in Longueuil]

Hi Daryl,

All DW788 (both model 1 & 2) have a lift arm assembly.

The DW788 is what is known as a top feeder as well as a bottom feeder scroll saw. And there is no need to tilt the table to change holes.

What you may be referring to is an add on called the EZ-Lift that keeps the arm in a lifted position, thus canceling the need for a piece of 2x4.

This is an inexpensive item that is bolted on to the side of the arm and uses a spring to keep the arm in a balanced raised position. Simple and effective.

Almost as necessary as a foot switch, in my opinion.

I personally think DeWalt should have made it part of their design, but I guess the engineer wasn't a scroller.

Regards,
Marcel

[Marsha]

Hi Daryl,
I totally agree with Marcel on this one. The Dewalt 788 is a very easy saw to use especially when doing fretwork. I first started scrolling on a Delta vs saw. The blade clamping system was such a pita that I rarely did any fretwork, and top feeding was next to impossible. Once I got my Dewalt and learned how to top feed, fretwork became a real joy to do. I don't have the EZ lift on my saw, and the only time I use a piece of 2 x 4 is when I'm doing compound cutting. When compound cutting you have to bottom feed because the arm does'nt lift high enough for top feeding.

I also understand the price of the Dewalt has come down substantially over the years. I've heard people are buying them as low as $ 400.00. The guy I got mine from paid over $ 700.00 CDN. for it, and that was at a Wood Show. I traded him a Hitachi router for the scrollsaw, so I got a real bargain. The router cost me $ 329.00 CDN.

So the bottom line for me would be to advise you to go for it. I'm sure you'll be real happy with a Dewalt.

Just my 2¢ worth
Marsha

[Sawduster]

Daryl,
Gotta chime in here too . I did a lot of research before I bought my saw and the DW788 seemed to be the best for the money ...I got the stand too.
I am extremely happy with it . The ease of blade changing/feeding alone makes it worth it to me . In my opinion you can't lose .....but you know what they say about opinions
Just my 2¢

[Daryl185]

hey thanks for the great info Marsha,Robert and Marcel thats just what I needed

[Marcel in Longueuil]

The DeWalt is not vibration free like the Eclipse, I'll admit as much.

But it doesn't interfere with my scrolling. The front to back movement of teh blade is normal in most scrollsaws due to the movement of the arm (known as a C assembly) If you imagine a letter "C" with the pivot point in the center of the vetical bar, and imagine it in an up and down movement while attached at the pivot point, you will see that it doesn't go straight up and down but rather has a little front to back motion as it raises & lowers.

The scrollsaw is the same way, some are more apparent then others, but the DeWalt isn't bad.

I'd recommend you visit Rick Hutchison's website, he recently posted a lot of interresting videos on top of the already good documentation he had available.

Regards,
Marcel

[brgordon]

have gone to Rich Hutcheson (I think thats were someone told me to go) Checked things over there and was greatly pleased with all the information there. Thanks. Now I need some help with my saw and Dewalt isn't very helpful. My Saw is bolted down to a 3/4" Plywood board which is bolted to a three leg table (now DeWalt) My speed control makes the saw vibrate very bad at speeds from 6 setting above. I today read a review of this saw on the net (not sure where right now) but the explaination was they could put a penny on the saw and it did not move. Well I can't put one on flat and keep it there from these 6 settings and above. Does anyone think by tightening linkage this could possible help this. My Warranty is good an I don't see where adjustment other then these would help. If I take it too a Service Center it will be a week or so before they look at it and I find this wrong. For this type of maintenance. The saw is great and I think I will be using it quite a lot when this is changed.

Thanks Bruce

[Gill]

First, I'd suggest you confirm that the problem does lie with your saw. Take it off the plywood base and table, put it on a concrete floor and see if it vibrates there before you try anything else.

Gill

[gmackay]

Daryl,

I own the Dewalt Dw788 Type 1 and type 2. I just went in my shop, balanced a nickle on the table 2" in front of the blade, tensioned the blade, and turned the saw on at speed 5. The nickle did not fall as I advanced to speed 8. It never fell.. Now my saw is mounted on a plywood and 2 x 4 table that I made so that I can sit while I scroll, so I know there is no vibration as the table probably weighs 40 pounds. Above speed 6 the blower nozzle did vibrate quite a bit, but, the table was steady.

Hope this helps, as the DW788 has been a good scroll saw for me for 9+ years.

Gary

[wwalker47]

Daryl,

I own a 788 as well, with the stand, light, and EZ lift. When mine came in it wasn't just right (something was clattering inside) and I took it to a DeWalt service center. They did an excellent job of tuning it up, under warranty, of course. It did take a week or so, but the time was well spent. Take it in and you will not regret it. It is a great saw for the money. I plan on having it for years to come.

Well that's my tupence.

-Bill