23" Craftsman Scroll Saw For Sale - Scroll Saw Woodworking & Crafts Message Board

bmeans · 08-10-2005, 10:06 PM

I have a saw that I inherited a couple years ago and have never used. The following specs apply:

Heavy cast iron base, table & yoke
TEFC direct drive, 1/6 HP, 2 speed (1725 & 825 SPM) motor.
23" throat capacity
2-5/8" thickness cutting capacity
20-1/2 x 10" adjustable table, w/insert and angle indicator (0-45 degrees)
Eye shield
Built-in dust blower
Blade tension control

I doubt the saw has been used for 2 hours, its just like new and everything works perfectly. I'm willing to accept any reasonable offer + shipping (if reqiired). I live in the Tampa Florida area. I hope someone can put this saw to work.

Anyone interested can reach me directly at brucemeans@verizon.net.

Thanks.

Woodbutcher68 · 08-11-2005, 02:28 AM

If it doesn't sell, donate it to your local Boys and Girls Club and offer to give lessons. Nothing like teaching new scrollers!

SharonW0111 · 08-13-2005, 05:57 AM

Not a bad saw if it has veriable speed and does it accept pinless and pinned blades. I have a craftsman and wish I could afford another but ..new one like he is speaking of sells $279 at sears .

08-10-2005, 10:06 PM	#1
bmeans Junior Member Join Date: Aug 2005 Posts: 1	23" Craftsman Scroll Saw For Sale I have a saw that I inherited a couple years ago and have never used. The following specs apply: Heavy cast iron base, table & yoke TEFC direct drive, 1/6 HP, 2 speed (1725 & 825 SPM) motor. 23" throat capacity 2-5/8" thickness cutting capacity 20-1/2 x 10" adjustable table, w/insert and angle indicator (0-45 degrees) Eye shield Built-in dust blower Blade tension control I doubt the saw has been used for 2 hours, its just like new and everything works perfectly. I'm willing to accept any reasonable offer + shipping (if reqiired). I live in the Tampa Florida area. I hope someone can put this saw to work. Anyone interested can reach me directly at brucemeans@verizon.net. Thanks.

08-11-2005, 02:28 AM	#2
Woodbutcher68 Senior Member Join Date: Aug 2005 Location: Hammond, IN Posts: 828	If it doesn't sell, donate it to your local Boys and Girls Club and offer to give lessons. Nothing like teaching new scrollers! __________________ Fred There's a fine line between woodworking and insanity, I'm just not sure which side of the line I'm on!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Craftsman 16" SS	Dawn	Tools and Blades	8	06-22-2007 03:10 AM
"The Man in Black" scroll saw portrait.	kerry_nf	Bragging Section	5	11-14-2006 03:07 AM
Old Craftsman 20" Contractors Question.	Randy	Tools and Blades	16	10-27-2006 08:26 PM
"Scroll portrait" finishing?	ontario026	General Scroll Saw	5	12-15-2005 01:15 AM
Review of Craftsman 20" Professional Grade Scroll saw	DaddyCakes	Tools and Blades	2	02-10-2005 09:29 PM

08-13-2005, 05:57 AM	#3
SharonW0111 Senior Member Join Date: Jul 2005 Location: Ne Texas Posts: 889	Not a bad saw if it has veriable speed and does it accept pinless and pinned blades. I have a craftsman and wish I could afford another but ..new one like he is speaking of sells $279 at sears .