Dw 788 - Scroll Saw Woodworking & Crafts Message Board

Hobbyhorse · 04-28-2005, 10:49 AM

Does anyone know where to obtain a Dewalt 788 scroll saw with a 240 volt 50Hz motor for use in New Zealand?

3_M · 04-28-2005, 03:37 PM

Contact DeWalt. They might have help for you.
I don't think you will find one in the US,
Mike M

Hobbyhorse · 04-29-2005, 07:15 AM

Thanks Mike but I have tried all of the Dewalt websites in New Zealand, Australia, Britain, and other continental countries that use 220 volt power and had no luck at all. They apparantly have a minimum order thus cannot order one only. I may just have to go to a Delta which is a shame.

Rhys H.

Scrollhead · 04-29-2005, 11:20 AM

Hobbyhorse, check at this site

http://www.woodworkforums.ubeaut.com...splay.php?f=19

and ask for Iain. He may be able to shed some light for ya.

Scrollhead

I also found this

http://www.dewalt.co.nz/main.asp?mktid=23&lid=1&sid=2

PiALaModem · 04-29-2005, 12:38 PM

Looking at the SAW website, I saw that there is a scrollsaw club listed in Australia. The contact name is Nick Schulz schulznj@picknow1.com.au

Try giving him a shout via email, perhaps he knows about resources in the region.

3_M · 04-29-2005, 07:04 PM

I believe Neil Schultz is the president of that club.
Neil Schultz schulznj@picknowl.com.au Australia
There is not much difference in the emal. It might be father and son.
Can you use any other motor?

Mike M

Hobbyhorse · 04-30-2005, 08:34 AM

Thanks guys. I have Emailed Nick and left a message on the Australian scrollers forum. We will see what eventuates.

Rhys H.

3_M · 04-30-2005, 03:29 PM

Here is one more email address. They have a lot of contacts with scrollers in Australia:
Owen/Helen Harris, ochjh@netconnect.com.au
Mike M

Gill · 05-12-2005, 09:17 AM

I hope I'm not too late with this info, but I've been told that the power system in New Zealand is the same as that in the UK. All you would need to do would be to change the plug, because New Zealand electrical outlets use plugs that are a different shape to the flat pins used in the UK.

It means that if you buy a power tool from the UK, it'll work in NZ. Unfortunately, I don't believe the DeWalt 788 is available in the UK.

Gill

Hobbyhorse · 08-23-2005, 09:24 AM

Thanks for all of the above comments. I gave up on the Dewalt and finally bought a Hegner from Australia. Just love it!!

Rhys H.

04-28-2005, 10:49 AM	#1
Hobbyhorse Senior Member Join Date: Apr 2005 Location: Auckland, New Zealand Posts: 294	Dw 788 Does anyone know where to obtain a Dewalt 788 scroll saw with a 240 volt 50Hz motor for use in New Zealand?

04-28-2005, 03:37 PM	#2
3_M Senior Member Join Date: Jan 2004 Location: Brandon, SD Posts: 628	Contact DeWalt. They might have help for you. I don't think you will find one in the US, Mike M __________________ Home of the FD Blades

04-29-2005, 07:15 AM	#3
Hobbyhorse Senior Member Join Date: Apr 2005 Location: Auckland, New Zealand Posts: 294	Dw 788 Thanks Mike but I have tried all of the Dewalt websites in New Zealand, Australia, Britain, and other continental countries that use 220 volt power and had no luck at all. They apparantly have a minimum order thus cannot order one only. I may just have to go to a Delta which is a shame. Rhys H.

04-29-2005, 11:20 AM	#4
Scrollhead Junior Member Join Date: Apr 2005 Posts: 16	Hobbyhorse, check at this site http://www.woodworkforums.ubeaut.com...splay.php?f=19 and ask for Iain. He may be able to shed some light for ya. Scrollhead I also found this http://www.dewalt.co.nz/main.asp?mktid=23&lid=1&sid=2 Last edited by Scrollhead; 04-29-2005 at 11:23 AM.

04-29-2005, 12:38 PM	#5
PiALaModem Senior Member Join Date: Feb 2005 Location: Norwalk, CT Posts: 185	Looking at the SAW website, I saw that there is a scrollsaw club listed in Australia. The contact name is Nick Schulz schulznj@picknow1.com.au Try giving him a shout via email, perhaps he knows about resources in the region. __________________ Steve Miklos, Luthier Carrot Creek Musical Instruments and Crafts http://www.carrotcreek.com "Edit twice, spell check, post once"

04-29-2005, 07:04 PM	#6
3_M Senior Member Join Date: Jan 2004 Location: Brandon, SD Posts: 628	I believe Neil Schultz is the president of that club. Neil Schultz schulznj@picknowl.com.au Australia There is not much difference in the emal. It might be father and son. Can you use any other motor? Mike M __________________ Home of the FD Blades

04-30-2005, 08:34 AM	#7
Hobbyhorse Senior Member Join Date: Apr 2005 Location: Auckland, New Zealand Posts: 294	Dewalt 788 scroll saw Thanks guys. I have Emailed Nick and left a message on the Australian scrollers forum. We will see what eventuates. Rhys H.

04-30-2005, 03:29 PM	#8
3_M Senior Member Join Date: Jan 2004 Location: Brandon, SD Posts: 628	Here is one more email address. They have a lot of contacts with scrollers in Australia: Owen/Helen Harris, ochjh@netconnect.com.au Mike M __________________ Home of the FD Blades

05-12-2005, 09:17 AM	#9
Gill Fallen Angel Join Date: Mar 2005 Posts: 2,625	I hope I'm not too late with this info, but I've been told that the power system in New Zealand is the same as that in the UK. All you would need to do would be to change the plug, because New Zealand electrical outlets use plugs that are a different shape to the flat pins used in the UK. It means that if you buy a power tool from the UK, it'll work in NZ. Unfortunately, I don't believe the DeWalt 788 is available in the UK. Gill

08-23-2005, 09:24 AM	#10
Hobbyhorse Senior Member Join Date: Apr 2005 Location: Auckland, New Zealand Posts: 294	Thanks for all of the above comments. I gave up on the Dewalt and finally bought a Hegner from Australia. Just love it!! Rhys H.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode