Do you have anywhere where I can show some of my Router / Engraved Designwork? - Scroll Saw Woodworking & Crafts Message Board

rogerjenkins · 01-09-2012, 08:27 AM

Search as I might through this site, I cannot seem to find a suitable location for some of my Aussie designs which are done with my 1/4" Router, and a Dremel attached to a router-base, & fitted with a 1/8" engraving tip.
Any helpful suggestions ?

BobD · 01-09-2012, 12:28 PM

Hi Roger,
If they're not scroll sawing, per sey, I'd put them in the Off Topic area. If they're more carving than scrolling, we've got an entire message board for carving at
Woodcarving Illustrated Message Board

Best Regards,
Bob Duncan
Technical Editor

journeyman · 01-09-2012, 05:56 PM

Put them in the "Off Topic" section Roger. We would love to see them.
Mick

rogerjenkins · 01-10-2012, 09:38 AM

Thank you for your assistance. Have placed editorial content about what I have been doing, along with the basic descriptions of three Router-cut signs I have recently done, and their accompanying photos in the, " Off Topic," section.
Got heaps more photos, most of which are on my new specialized website for my Wooden Signs.

01-09-2012, 08:27 AM	#1
rogerjenkins Member Join Date: Jul 2011 Location: Port Vincent, South Australia Posts: 64 Thanks: 0 Thanked 0 Times in 0 Posts	Do you have anywhere where I can show some of my Router / Engraved Designwork? Search as I might through this site, I cannot seem to find a suitable location for some of my Aussie designs which are done with my 1/4" Router, and a Dremel attached to a router-base, & fitted with a 1/8" engraving tip. Any helpful suggestions ? __________________ Roger www.easysell.com.au/rogerjenkins " If it don't work first time, then try again, then IF that don't work, recycle the project into something else, or go to plan No. 421 which is,------------

01-09-2012, 12:28 PM	#2
BobD Technical Editor Join Date: Aug 2004 Location: Lebanon, Pa Posts: 3,386 Blog Entries: 2 Thanks: 10 Thanked 32 Times in 25 Posts	Hi Roger, If they're not scroll sawing, per sey, I'd put them in the Off Topic area. If they're more carving than scrolling, we've got an entire message board for carving at Woodcarving Illustrated Message Board Best Regards, Bob Duncan Technical Editor __________________ www.WoodCarvingIllustrated.com www.FoxChapelPublishing.com www.ScrollSawer.com Shopsmith, Hawk G4

01-09-2012, 05:56 PM	#3
journeyman Rock 'n Scroller Join Date: Dec 2008 Location: Yorkshire, England Posts: 1,602 Thanks: 12 Thanked 16 Times in 15 Posts	Put them in the "Off Topic" section Roger. We would love to see them. Mick __________________ Don't worry if people are talking behind your back. - It simply means you are two steps ahead of them

01-10-2012, 09:38 AM	#4
rogerjenkins Member Join Date: Jul 2011 Location: Port Vincent, South Australia Posts: 64 Thanks: 0 Thanked 0 Times in 0 Posts	Thanks guys,- have placed photos in " Off Topic." Section Thank you for your assistance. Have placed editorial content about what I have been doing, along with the basic descriptions of three Router-cut signs I have recently done, and their accompanying photos in the, " Off Topic," section. Got heaps more photos, most of which are on my new specialized website for my Wooden Signs. __________________ Roger www.easysell.com.au/rogerjenkins " If it don't work first time, then try again, then IF that don't work, recycle the project into something else, or go to plan No. 421 which is,------------

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CNC Router	evilbadger	Tools and Blades	5	09-14-2011 12:41 AM
Router	bronco	General Scroll Saw	14	01-03-2010 12:57 PM
Router	Dragon	Off Topic	15	01-26-2007 03:04 PM
Laser engraved plates	Dale_O	Welcome Members	0	06-23-2003 01:42 PM