Is this possible?!?!? - Scroll Saw Woodworking & Crafts Message Board

wickens · 05-09-2006, 03:33 PM

I would like to make a small ornate box like the picture below. Is it possible to do this with my scroll saw if I make it in slices and laminate it? box.jpg
If the picture isn't viewable please check out the website.
http://wavesinwood.justcollectingdust.com/ovals.html

Thanks
Pat

BobD · 05-09-2006, 03:39 PM

It's definately possible. Check out the Monogram Keepsake Box Rhys madein our last issue. These boxes are based on the same principle.

Bob Duncan
Technical Editor
Scroll Saw Woodworking & Crafts

(Bob, who always gives his credentials the first time he responds to a new poster <grin>)

Marcel in Longueuil · 05-09-2006, 07:27 PM

C'mon BobD,

Admit that you wanted to throw that new name for the mag in here somewhere

Regards,
Marcel

BobD · 05-09-2006, 08:08 PM

I had to change the way I think (I'm working on the new issue with the new name as we speak)...It took me forever to remember, so I deserve to be able to gloat a little <grin>

Bob

lucky788scroller · 05-09-2006, 08:29 PM

Your doing a great job Bob, keep it up. dale

(the guy who just goes by dale, lucky, or a number of names not fit for this site)

05-09-2006, 03:33 PM	#1
wickens canadiancajun Join Date: May 2006 Location: Covington, Louisiana Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts	Is this possible?!?!? I would like to make a small ornate box like the picture below. Is it possible to do this with my scroll saw if I make it in slices and laminate it? box.jpg If the picture isn't viewable please check out the website. http://wavesinwood.justcollectingdust.com/ovals.html Thanks Pat

05-09-2006, 03:39 PM	#2
BobD Technical Editor Join Date: Aug 2004 Location: Lebanon, Pa Posts: 3,379 Blog Entries: 2 Thanks: 10 Thanked 27 Times in 21 Posts	It's definately possible. Check out the Monogram Keepsake Box Rhys madein our last issue. These boxes are based on the same principle. Bob Duncan Technical Editor Scroll Saw Woodworking & Crafts (Bob, who always gives his credentials the first time he responds to a new poster <grin>) __________________ www.WoodCarvingIllustrated.com www.FoxChapelPublishing.com www.ScrollSawer.com Shopsmith, Hawk G4

05-09-2006, 07:27 PM	#3
Marcel in Longueuil Gone to the Dark Side Join Date: Mar 2006 Location: Québec, Canada Posts: 1,069 Thanks: 0 Thanked 0 Times in 0 Posts	C'mon BobD, Admit that you wanted to throw that new name for the mag in here somewhere Regards, Marcel __________________ http://marleb.com DW788. -Have fun in the shop or it isn't a hobby anymore. NOTE: No trees were killed in the sending of this message, but a large number of electrons were terribly inconvenienced.

05-09-2006, 08:08 PM	#4
BobD Technical Editor Join Date: Aug 2004 Location: Lebanon, Pa Posts: 3,379 Blog Entries: 2 Thanks: 10 Thanked 27 Times in 21 Posts	I had to change the way I think (I'm working on the new issue with the new name as we speak)...It took me forever to remember, so I deserve to be able to gloat a little <grin> Bob __________________ www.WoodCarvingIllustrated.com www.FoxChapelPublishing.com www.ScrollSawer.com Shopsmith, Hawk G4

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-09-2006, 08:29 PM	#5
lucky788scroller Senior Member Join Date: Sep 2005 Location: wisconsin Posts: 6,308 Thanks: 0 Thanked 0 Times in 0 Posts	Your doing a great job Bob, keep it up. dale (the guy who just goes by dale, lucky, or a number of names not fit for this site)