Welcome to Scroll Saw Woodworking & Crafts Message Board, an online scroll saw forum community where you can join thousands of scrollers from around the world discussing all things related to Scrolling. To gain full access to the message board you must register for a free account.
As a registered member you will be able to:
* Browse over 200,000 posts.
If you have any problems with the registration process or your account login, please contact the Scroll Saw Woodworking & Crafts Support Team.
|General Scroll Saw|
| ||LinkBack||Thread Tools||Display Modes|
|11-25-2013, 10:32 PM||#1|
Pictures of New PC Scroll Saw PCB375SS
A few pics
Last edited by hotshot; 11-25-2013 at 10:39 PM.
|11-25-2013, 11:05 PM||#3|
And who manufacturers this Saw? gotta love the internet . . . . Rexon it is, and designated to Lowes. In this shipment was 350 saws. This saw is 18", so that gives this entry saw two more inches than the 370ss. Motor 1.6 AMP, 500 to 1500 strokes per minute, table size 12 5/8 by 20"
Last edited by hotshot; 11-25-2013 at 11:48 PM.
|11-25-2013, 11:44 PM||#4|
Join Date: Apr 2013
Location: Pinelog Creek, FL
Thanked 109 Times in 102 Posts
Wow Hotshot.. you are da man!
This looks like a positive upgrade to the 370ss. It will be interesting to see the test results!
If Rexon/ Porter Cable made even a few positive upgrades over the older model, and can keep the QC in the positive, then they can take over the Sub $250 entry level market.
It would be nice to see an arm lift setup, but I believe that if they put out a good entry level unit that would help the scroll saw community as a whole get some new younger blood.
Pinelog Creek, FL
DW788 Owner since 2013
"Like a wind crying endlessly through the universe, time carries away the names and the deeds of conquerors and commoners alike.
And all that we were, all that remains is in the memories of those who cared we came this way for a brief moment."
|11-26-2013, 12:28 AM||#5|
Join Date: Jul 2013
Location: Port Angeles, Wa
Thanked 117 Times in 107 Posts
Wow! I like the knob on the clamps. I have a dilly of a time some times to change the blades on my Shop Fox as I have to use an allen wrench or hex wrench to loosen a little screw and then put in the blade. At least I have no problem with the clamps cracking if I should over tighten. Wish I could find a saw like that one. It looks like a better quality saw than the Shop Fox. We don't have a Lowes in our area. I would have to go to Silver Dale to look at their saws. One of these days maybe I will or get Big Yellow. Thanks for sharing these pictures. Have a great evening Fay
|11-27-2013, 05:50 AM||#6|
Join Date: Feb 2007
Thanked 18 Times in 18 Posts
I was at Lowes yesterday, and they didn't have the new saw yet. But the old style PC is on sale for $129. That's $60 off. If you show your Veteran card, 10% more off.
|11-27-2013, 09:41 AM||#7|
It might just be me, but it almost looks by that that pic that the rear of the saw is elevated a little by the stand. The stand definitely has some 788 influence.
$129 for the old model seems to be a steal. I doubt Rexon will quit making that model since it is sold under so many different names. I would think parts should be plenteous for a while.
|12-18-2013, 08:54 AM||#8|
Join Date: Dec 2013
Thanked 1 Time in 1 Post
I purchased one last night.
I haven't used except to cut some 1/4" red oak just to test it out. The only vibration I had was from the little tray that holds the spare blades under the table. The stand does not angle down, it just appears that way because the stand is closer together in the back than it is in the front.
|The Following User Says Thank You to EvilRick For This Useful Post:|| |
Terry Murphy (12-18-2013)
|12-18-2013, 10:31 AM||#9|
Join Date: Apr 2005
Location: Bellport, LI New York
Thanked 445 Times in 399 Posts
When you have a bit more time please give us an update on the saw (after using it for a while)
Front to back blade motion would be of interest to me.
It would be great if this were to become a reasonable entry level saw.
RBI G4 Hawk, Delta SS350, Nova 1624 DVR XP
Philosophy "I don't know that I can't, therefore I can"
Proud Member of the Long Island Woodworkers Club
And the Long Island Scrollsaw Association
Last edited by Rolf; 12-18-2013 at 12:09 PM.
|12-18-2013, 11:41 AM||#10|
Join Date: Nov 2008
Location: Coeur d'alene. Idaho
Thanked 113 Times in 111 Posts
Where did you buy it, and does it come with the stand or is it extra?
It's all fun
Delta 46-460 lathe