Welcome to Scroll Saw Woodworking & Crafts Message Board, an online scroll saw forum community where you can join thousands of scrollers from around the world discussing all things related to Scrolling. To gain full access to the message board you must register for a free account.
As a registered member you will be able to:
* Browse over 200,000 posts.
If you have any problems with the registration process or your account login, please contact the Scroll Saw Woodworking & Crafts Support Team.
|General Scroll Saw|
| ||LinkBack||Thread Tools||Display Modes|
|12-16-2009, 05:09 PM||#1|
A Few Name Plates
Well just to let everyone know that I still do scroll when it is needed. This was the third order from the same person. I have about 6 hours in this project maybe start to finished. I never really kept good track of the time. I did all the designing, cutting and gluing one day and the spray can finish the second day.
But I am still spending most days playing on the wood lathe making more bowls. I had to start stacking them on the floor because the shelf is full.
Last edited by Rick-H; 12-16-2009 at 05:11 PM.
|12-16-2009, 05:17 PM||#2|
scroller and moderator
Join Date: Dec 2006
Location: Chertsey, Quebec, Canada
Thanked 9 Times in 9 Posts
Wow! Rick, you sure have been busy. I like the base on the name plates. What are you going to do with all these bowls? My birthday isn't until June....:-)
Owner of a nice 21" Excalibur
Owner of a Dewalt 788
PuffityDragon on AFSP
|12-16-2009, 05:34 PM||#3|
That is not all of the bowls, maybe a third of what I have turned and on hand. But I have enough wood here waiting to do that many easily again. Turning is so addictive, I think worse than scrolling.
|12-16-2009, 07:02 PM||#4|
Join Date: Dec 2005
Location: Stevens Point, WI
Thanked 0 Times in 0 Posts
Wow, Rick. Where do you get all that energy. I know that you are a speed scroller, but 6 hours? You are an ambitious fellow. And I like those bowls. All for sale or do you donate to charities as well?
|12-16-2009, 07:15 PM||#5|
Join Date: Sep 2008
Thanked 4 Times in 3 Posts
Now that's what I call some serious bowls! I'd like to see more pictures of those.
|12-16-2009, 07:22 PM||#6|
If you go to my web site I have a whole section now on turning. I have more pictures in the "New Display Area" section of what I have been turning. Also at the bottom of the turning section index check the "Delta 46-460 Lathe" for more pictures. Just look around all the turning pages really.
Right now I just keep stacking them up. If something came up in the way of a local charity they might get a few.
|12-16-2009, 07:38 PM||#7|
Grandpa making Sawdust
Join Date: Nov 2005
Location: Aumsville, Oregon
Thanked 1,075 Times in 740 Posts
How do you do the bases? Is that a blind/stop dado and then insert the name?
"Still Montana Mike"
There is a very fine line between “hobby” and “mental illness.”
As You Slide Down the Banister of Life, Pray That All The Splinters Are Pointed The Other Way...
"Don't worry about old age--it doesn't last that long."
Mike's Wood-n-Things LLC
|12-16-2009, 07:54 PM||#8|
Join Date: Mar 2007
Location: Riverton, KS on Route 66
Thanked 2 Times in 2 Posts
Thou hast been very busy Rick. Very nice work of course.
|12-16-2009, 08:24 PM||#9|
I design the name with Corel Draw. The names are cut then I cut a, 2 1/8" wide by 1 1/2" longer than the name, block of wood. Then rout the edge on the router table, sand all then glue the name to the base.
Last edited by Rick-H; 12-16-2009 at 08:27 PM.
|Thread||Thread Starter||Forum||Replies||Last Post|
|Name plates||marshall||Fretwork and Portraits||12||10-27-2011 03:37 AM|
|Plates||PatteM||Fretwork and Portraits||7||04-03-2011 11:48 PM|
|Another 3 plates||florintina2001||General Scroll Saw||12||08-20-2009 11:16 AM|
|Another 2 plates||florintina2001||General Scroll Saw||12||08-14-2009 10:37 AM|
|Name plates||marshall||Fretwork and Portraits||14||03-04-2009 11:17 PM|