Finished my second portrait - Scroll Saw Woodworking & Crafts Message Board

snackman41 · 02-03-2009, 04:13 AM

Hi everyone, thanks to Chris and Kevin for creating patterns for me. Both were incredible but I used Chris' for the close-up. well here it is.

dragyn · 02-03-2009, 12:56 PM

Wonderful job on that.

Wood Dog · 02-03-2009, 02:17 PM

Sweeeeeet project snackman41......what size blade did you use? I assume it was a spiral though?

catslover64 · 02-03-2009, 05:12 PM

Nice work.

snackman41 · 02-03-2009, 05:29 PM

I Mostly used #2 Reverse and #2 Skip Tooth. I only used a Spiral Blade on two Cuts because I Need the cuts to come to sharp points and I'm not that good using a spiral blade.

unixpro · 02-04-2009, 11:10 PM

Very nice. Are you going to frame it?

snackman41 · 02-05-2009, 12:26 AM

Yes It is framed in a black frame but I didn't include it in the picture so I could get a closer shot.

kerry_nf · 02-07-2009, 04:27 PM

Wonderful work. Next time, take the pic without the glass in the frame so you don't have any reflection.

snackman41 · 02-08-2009, 04:34 AM

Thanks Kerry, That is good advise. I realized after I took the picture that it had a glare. It would definitely look better without the glass. I hope to someday learn how to make the patterns but until then, many thanks to you that are so talented in pattern making. Without you. I wouldn't be able to make these for my kids.
Mike

marshall · 02-08-2009, 12:05 PM

A lot of cuts , fine jobs .

.............Marshall

02-03-2009, 02:17 PM	#3
Wood Dog Senior member--Absolutely Join Date: Jul 2007 Location: MA USA Posts: 3,908	Sweeeeeet project snackman41......what size blade did you use? I assume it was a spiral though? __________________ WD

02-03-2009, 05:29 PM	#5
snackman41 Member Join Date: Dec 2008 Location: Colorado Posts: 43	Blades I Mostly used #2 Reverse and #2 Skip Tooth. I only used a Spiral Blade on two Cuts because I Need the cuts to come to sharp points and I'm not that good using a spiral blade.

02-05-2009, 12:26 AM	#7
snackman41 Member Join Date: Dec 2008 Location: Colorado Posts: 43	Yes Yes It is framed in a black frame but I didn't include it in the picture so I could get a closer shot.

02-07-2009, 04:27 PM	#8
kerry_nf Senior Member Join Date: Nov 2006 Posts: 727	Wonderful work. Next time, take the pic without the glass in the frame so you don't have any reflection. __________________ Check me out on the web: http://www.kerrysworld.com

02-08-2009, 04:34 AM	#9
snackman41 Member Join Date: Dec 2008 Location: Colorado Posts: 43	Thanks Thanks Kerry, That is good advise. I realized after I took the picture that it had a glare. It would definitely look better without the glass. I hope to someday learn how to make the patterns but until then, many thanks to you that are so talented in pattern making. Without you. I wouldn't be able to make these for my kids. Mike Last edited by snackman41; 02-08-2009 at 04:40 AM.

02-03-2009, 12:56 PM	#2
dragyn Local Goofball! Join Date: Jan 2009 Posts: 2,007	Wonderful job on that. __________________ Dragyn (Oh my! Another Mike! ) It's a good thing my head is attached to my ... ... Has anyone seen my head?!?

02-03-2009, 05:12 PM	#4
catslover64 Senior Member Join Date: Nov 2008 Location: York, PA Posts: 122	Nice work.

02-04-2009, 11:10 PM	#6
unixpro I need more weekend Join Date: Dec 2006 Location: Greater Seattle Area Posts: 692	Very nice. Are you going to frame it?

02-08-2009, 12:05 PM	#10
marshall Just love Being Here Join Date: May 2008 Location: Jonesboro Arkansas { USA } Posts: 2,636	A lot of cuts , fine jobs ..............Marshall __________________ Usually busier than a cat in a sandbox !!!!!!!!!!! { Dewalt 788 only }

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode