Result of AFSP/SSW&C forum merger? - Scroll Saw Woodworking & Crafts Message Board

Opa Tuck · 11-08-2008, 05:25 PM

The word 'never' was in the column of last post. Would that mean that the Scroll Saw Pattern Vault is a result of the merger of the two forums since MSN Groups is going (or has gone) away? If so, then I want to extend my thanks to SSW&C for offering the opportunity for AFSP to merge with them. I, and I'm sure many others, certainly appreciate it. I haven't had much time to actually operate my scrollsaw but I want plenty of "ammunition" when I finally get to that point in my life. Thanks again SSW&C!!

Opa Tuck

waboese2006 · 11-08-2008, 05:46 PM

How does one access the scroll saw pattern vault?

Jediscroller · 11-08-2008, 06:03 PM

I'm going to be test posting a few patterns here today. We'll be populating the vault as time progresses. We want to make sure that we honor the wishes of all of the designers from AFSP.
The word "never" referred to the last post, as this was a new board, this was the first thread.

sparkyky · 11-08-2008, 06:06 PM

Waboese We are still in the process of going through the vault before we move it here.... It may take us a little while to get
everything gone through.

Jody

Jediscroller · 11-08-2008, 06:18 PM

As a test run, I just created the first of the vault (the stuff to get started with).

Hey Jody, I thought we both said we were taking a break, hehehehehe.

greatdane2 · 11-08-2008, 06:32 PM

Hi Kevin, I relize you are being overwelmed with all the new stuff. But in the future is it possible to change how the new posts work. It would be nice if when we are on say page 3 of the new posts that we could stay there. Now if we look at a post and want to go to the next one it kicks us back to page 1 and then we plug in 2 or 3.
This is a very small request that should be put on the bottom of the pile, just would be nice to have done.

Thanks, Alan.

Jediscroller · 11-08-2008, 07:00 PM

Alan,
Not sure why this happened? I just noticed this myself. We should be able to set this in our option, I will go check.

Messman · 11-09-2008, 04:47 AM

I just moved over from AFSP and would like to thank those here at SSW&C for allowing this merger to take place

wjbclocks1 · 11-09-2008, 09:19 PM

Kevin
Thanks for all your hard wook to keep us together

wood-n-things · 11-09-2008, 09:21 PM

Quote:

Originally Posted by Jediscroller

Alan,
Not sure why this happened? I just noticed this myself. We should be able to set this in our option, I will go check.

Kevin any updates on this issue?

11-08-2008, 05:25 PM	#1
Opa Tuck Junior Member Join Date: Nov 2008 Posts: 1	Result of AFSP/SSW&C forum merger? The word 'never' was in the column of last post. Would that mean that the Scroll Saw Pattern Vault is a result of the merger of the two forums since MSN Groups is going (or has gone) away? If so, then I want to extend my thanks to SSW&C for offering the opportunity for AFSP to merge with them. I, and I'm sure many others, certainly appreciate it. I haven't had much time to actually operate my scrollsaw but I want plenty of "ammunition" when I finally get to that point in my life. Thanks again SSW&C!! Opa Tuck

11-08-2008, 06:03 PM	#3
Jediscroller American Crafstman Join Date: Jul 2005 Location: Galaxy far, far away Posts: 3,174 Blog Entries: 5	I'm going to be test posting a few patterns here today. We'll be populating the vault as time progresses. We want to make sure that we honor the wishes of all of the designers from AFSP. The word "never" referred to the last post, as this was a new board, this was the first thread. __________________ Kevin Scrollsaw Patterns Online Making holes in wood with an EX-30, Craftsman 16" VS, Dremel 1680 and 1671

11-08-2008, 06:18 PM	#5
Jediscroller American Crafstman Join Date: Jul 2005 Location: Galaxy far, far away Posts: 3,174 Blog Entries: 5	As a test run, I just created the first of the vault (the stuff to get started with). Hey Jody, I thought we both said we were taking a break, hehehehehe. __________________ Kevin Scrollsaw Patterns Online Making holes in wood with an EX-30, Craftsman 16" VS, Dremel 1680 and 1671

11-08-2008, 07:00 PM	#7
Jediscroller American Crafstman Join Date: Jul 2005 Location: Galaxy far, far away Posts: 3,174 Blog Entries: 5	Alan, Not sure why this happened? I just noticed this myself. We should be able to set this in our option, I will go check. __________________ Kevin Scrollsaw Patterns Online Making holes in wood with an EX-30, Craftsman 16" VS, Dremel 1680 and 1671

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-08-2008, 05:46 PM	#2
waboese2006 Junior Member Join Date: Nov 2008 Posts: 1	How does one access the scroll saw pattern vault?

11-08-2008, 06:06 PM	#4
sparkyky Moderator Join Date: Jul 2006 Posts: 131	Waboese We are still in the process of going through the vault before we move it here.... It may take us a little while to get everything gone through. Jody

11-08-2008, 06:32 PM	#6
greatdane2 Dumb Member Join Date: May 2008 Location: Vancouver Island, BC. Canada Posts: 2,225	Hi Kevin, I relize you are being overwelmed with all the new stuff. But in the future is it possible to change how the new posts work. It would be nice if when we are on say page 3 of the new posts that we could stay there. Now if we look at a post and want to go to the next one it kicks us back to page 1 and then we plug in 2 or 3. This is a very small request that should be put on the bottom of the pile, just would be nice to have done. Thanks, Alan.

11-09-2008, 04:47 AM	#8
Messman AFSP Join Date: Nov 2008 Location: Florida Posts: 211	I just moved over from AFSP and would like to thank those here at SSW&C for allowing this merger to take place

11-09-2008, 09:19 PM	#9
wjbclocks1 Senior Member Join Date: Nov 2008 Posts: 213	Kevin Thanks for all your hard wook to keep us together